Description
W3G800-NE57-53 ebm-papst EC axial fan axial; 400VAC; Ø1020x346mm; 12060m3/h; ball; 720rpm; IP55 AxiCool
Part # Alias: W3G800NE5753
Nominal data
Phase 3~
Type of voltage AC
Nominal voltage in V 400
Nominal voltage range in V 380 .. 480
Frequency in Hz 50/60
Type of data definition maximum load
Speed in min-1 720
Power input in W 660
Current draw in A 1
Max. back pressure in Pa 110
Min. ambient temperature in °C -40
Max. ambient temperature in °C 40
Airflow Direction
V
Protection Class
IP55
Frequency
50/60
Input Power
660
Phase
3~
Rated Voltage
400
Speed
720
Current Draw
1
Min. Ambient Temperature
-40
Max. Ambient Temperature
40
Certification
CSA C22.2 No. 77 + CAN/CSA-E60730-1 / UL 1004-7 + 60730-1 / EAC
Size
800 mm
Fan Type
EC axial with wall ring
Voltage Range
380 … 480
Rotor Material
Pressed sheet steel, coated with PP plastic
Voltage Type
AC
Motor Protection
Thermal Overload Protection (TOP) internally connected
Motor Size
112
Insulation Class
F
Protection Class against Moisture (F) / Environment (H)
H2
Motor Bearings
Ball bearings with low-temperature grease
Max. Back Pressure
110
Rotor Surface
Black painted
Electronics Housing Material
Die-cast aluminum, black painted
Max. Permissible Ambient Temp. (Transport/Storage)
70
Min. Ambient Temp. (Transport/Storage)
-40
Fan Housing Material
PP plastic
Weight
32 kg
Standards Compliance
EN 61800-5-1 / CE
Motor: M3G112-GAWeight 32 kg,Motor size 112 ,Size 800 mm,Rotor surface Painted black ,Electronics housing material Die-cast aluminum, painted black ,Blade material Press-fitted sheet steel blank, sprayed with PP plastic ,Fan housing material PP plastic ,Material guide vanes PP plastic ,Guard grille material Steel, coated with black plastic (RAL 9005) ,Number of blades 5 ,Airflow direction V ,Direction of rotation Clockwise, viewed toward rotor ,Degree of protection IP55 ,Insulation class “F” ,Ambient temperature note If there is a risk of ice formation, the fan is only to be operated with a heating tape in the fan housing. Further information can be obtained from ebm-papst. As fan only suitable for use with industrial evaporators ,Moisture (F) / Environmental (H) protection class H2 ,Max. permitted ambient temp. for motor (transport/storage) +70 °C,Min. permitted ambient temp. for motor (transport/storage) -40 °C,Installation position See fitting instructions ,Condensation drainage holes On rotor side ,Mode S1 ,Motor bearing Ball bearing with low-temperature lubricant ,Technical features – Output 10 VDC, max. 10 mA – Operation and alarm display – External 24 V input (parameter setting) – Alarm relay – Integrated PID controller – Motor current limitation – PFC, passive – RS-485 MODBUS-RTU – Soft start – EEPROM write cycles: 100,000 maximum – Control input 0-10 VDC / PWM – Control interface with SELV potential safely disconnected from the mains – Thermal overload protection for electronics/motor – Line undervoltage / phase failure detection ,EMC immunity to interference According to EN 61000-6-2 (industrial environment) ,EMC circuit feedback According to EN 61000-3-2/3 ,EMC interference emission According to EN 61000-6-3 (household environment) ,Touch current according to IEC 60990 (measuring circuit Fig. 4, TN system) <= 3,5 mA,Motor protection Thermal switch auto reset, internally connected ,Protection class assignment I; If a protective earth is connected.|The built-in component has several local protection class assignments.|The final protection class is determined by the intended installation. ,Conformity with standards EN 61800-5-1 / CE ,Approval CSA C22.2 No. 77 + CAN/CSA-E60730-1 / UL 1004-7 + 60730-1 / EAC
Datasheet: /ds/W3G800-GT.pdf
